Clamp takes about 15 cm on the turntable.
After wrapping the pallet ,the turntable shall come back stand by replace ,clamp with catch the film tail. And then make film cut, all the movie is automatically, with Romote control..
Wrapping Range :
L min. * W min. –500mm * 500 mm.
L max. * Wmax – 1200mm * 1200 mm.
Turntable diameter 2000mm Turntable Height 85mm
Turntable weight capacity 2000kg
Wrapping height: 2700mm
Machine weight 550kg
Power supply 220V 50/60HZ 1Phase (standard)
Packing efficiency 20-40 loads / hour
LLDPE – Stretch Film
Film Thickness 17-35 µm
Film Width 500 mm
Core Diameter 76.2 mm
Maximum Film. Diameter 260 mm
Max. weight of film roll 15 kg
Film clamp device in pneumatic on turntable.
1.Parameter of the mechanical construction:
Turntable diameter:1800mm (Max packing dimension:L1200*W1200mm)
Turntable height from the floor:80mm
Height of mechanical column:2000mm (Packing height:up to 1800mm)
Cut system with heating wire and brush
Pre-stretch Motor and film carriage system(Stretch rate up to 250-300%).
6-8 wheels under the turntable for rotating smoothly and low noise.
2.PARAMETER OF ELECTRIC ELEMENTS
PLC: Fatek (Taiwan)
Inverter: Zhongcheng (Taiwan)
Sensor (To detect the height of pallet): B+F (Germany)
proximate switch(Memory No of rotation of turntable): Yangming (Taiwan)
Limit switch(Limiting min/max packing height):Schneider(France)
Film Carriage Gear Motor:Chenggang/OT (China)
Turntable Gear Motor:Luyang (Taiwan)
Up-down AC motor:Jinglong (China)
Air Filter and Pneumatic System:Air-Tac Brand (Taiwan)
Touchable screen and inside column of above.
Control pannel manual (in touchable screen.)
* Production: 20-40 pallets per hour
* Adjustable stretch film tensioner with frequency inverter;
* Motorized pre-stretching the film to 180% to 300%;
* Platform with up to 2,000 kg;
* Photocell for reading the various heights of the pallets;
* Adjustment of the number of upper and lower laps;
* Platform turntable Stops always at the same point;
* Platform turntable diameter 2000 mm;
* Useful height of 2 m (aluminum column);
* All motors, controlled inverters frequency to optimize the packaging;
* Tweezers Group, the film cutting arm: pneumatic;
* Electrical panel: Delta or Yonghong PLC.
* Remote control for start-up;
* No operator needing.
*The arm is required to HOLD and AUTOMATIC FILM CUTTING
This machine would be control by remote. (remote control) this is optional 。
*Photo-eye auto-height sensing pallet height
*Separate top ,bottom & up-down &reinforcement Wrap Counter Selector0-9
*Over-wrap count to create a cover
*Reinforce wrap count to keep goods stable
*Film Tension Control adjustment on the panel
*Separate start, pause and emergency stop buttons
*Manual carriage up/down control
*Variable Turntable Speed control
*Carriage up/down speed control
*1650mm Diameter Structural steel plate
*300 mm Height (floor to top of turntable)
*8mm steel plate thickness
*0-13rpm variable turntable speed by frequency changer
*Position turntable alignment
*Anti wear nylon sport rings, low noise, high quality
*Powder pre-stretch film holder
*Door open for easy threading
*Powered pre-stretch system up to 250%, standard 200%
*Film delivery variable speed by separate AC Drive Motor
*Electronic film tension control adjustment on panel
Trailing edge of the stretch film (the tail) hanging from the pallet must be automatically applied to the load. Positive film tail treatment ensures that the sagging tail does not hang up or unravel during transit or at the customer’s location.
Hold the leading edge (tail) of stretch film to allow the start of the stretch wrapping cycle without the need of an operator to attach the stretch film to the load.
After completion of the stretch wrapping cycle the stretch film must be cleanly cut from the pallet load and positively secured in a clamp so that the leading edge of the stretch film is positioned so that subsequent pallets can be stretch wrapped.
*Heavy duty double-chain carriage lift, calm and safety, fully guarded,Economical model is single chain carriage lift.
*Film carriage variable speed control on the panel
*The path to place and hold the pallet on the turntable, make it easier to load the whole pallet
Main Parts List:
² PLC ALLEN BRADLEY （AMERICA）
² TRANSDUCER HLP （DENMARK）
² AC CONNECTOR SCHNEIDER （FRANCE）
² URGENT STOP SCHNEIDER （FRANCE）
² PROCES SWITCH SCHNEIDER （FRANCE）
² PHOTOELECTRIC SWITCH OMRON （JAPAN）
² APPROACH SWITCH OMRON （JAPAN）
² REDUCTION WITH GEAR BOX TY （CHINA）
² MOTOR WITH REDUCTION GEAR BOX TYT (TAIWAN)
² DC MOTOR （CHINA）
² CONNECTION END PHOENIX （GERMANY）